![]() I see that you have the UPR DVCC and their breather cap as well. A more permanent solution would be to add a catch can to separate the oil from the PCV return to the intake. That won't be necessarily be fixed by raising the idle. I can see how that would be a bandaid fix for the smoking, but the real issue is that the engine is ingesting oil and water vapor that creates smoke in the exhaust. ![]() Raising the idle would decrease the vacuum which would decrease the effectiveness of the PCV system. We spent several months tuning this car, but we may not have had the time with the mods to notice the idle smoke issue you're mentioning. If you need assistance installing the driver, please contact Hypertech’s Tech Support.Good question! Although we did mod our test vehicle with full exhaust and high flow catted downpipe we didn't see any issues with smoke at idle. Please choose the instruction that matches your Windows operating system version. The driver installation can vary between versions of Windows. Please note the location on the PC where the file is downloaded to.Īfter the driver has been downloaded, please visit the following link to FTDI’s installation instructions. To download the driver, look for Windows row under the Operating System column and then click on “setup executable” in the Comments column. To download the latest version of the FTDI driver, visit the following link at. If for some reason the FTDI USB drivers are not installed and will not automatically install, the drivers will have to manually downloaded and installed. This is a function of Windows and not the Inline Speedometer Calibrator software. Please note that when Windows attempts to automatically install the USB drivers that it can take as long as 10 minutes to complete. This is an automatic process for most Windows operating systems configurations. If the drivers are not currently installed on the target PC, Windows will attempt to automatically download and install the latest version of the FTDI USB drivers. For most users these drivers are more than likely already installed on the target PC and no additional steps are required. The module utilizes a Windows USB driver supplied by Future Technologies Devices International (FTDI). Hypertech Products communicates with its accompanying configuration software via USB. How to Download the Standalone USB Driver Installer Note: The REACT Tuning Optimizer software is ONLY compatible on a Windows-based computer. You can now reconnect your REACT APP Module and Controller Module. Once you’re done making changes to a curve or importing a new Tune Set, click the “Write to Module” button, followed by the "Disconnect From APP” button, and exit the program. ![]() You can now adjust your own curves, save the curve set, or store another curve set on your REACT APP Module that you got from a friend or tuner in your Car/Jeep/Truck club. Plug the small end into the REACT APP Module and the large end into your laptop or PC. Once installed, open the Tuning Optimizer software and connect the REACT APP Module (not the Controller Module) to your PC or Windows laptop via the supplied micro USB cable (the cable that connects the REACT APP Module with the REACT Controller Module). ![]() Hypertech developed the REACT Tuning Optimizer software to allow you to develop your own custom pedal curves if you want to further customize your throttle response. There is also a button below that will guide you through the update process. The internet update software is only available for computers running Windows 7, Windows 8.1, and Windows 10. After the installer is downloaded to the computer, simply run the installer and follow the on-screen prompts for installation. The Inline Speedometer Calibrator Configuration software is no longer available as standalone download.Ĭlick the button below to download the latest version of the Tuner Update software installer. It does not update the Inline Speedometer Calibrator device firmware. The Inline Speedometer Calibrator Configuration software is used to configure the Inline Speedometer Calibrator device for the correct application and tire and gear value changes. The Inline Speedometer Calibrator Configuration software can now be launched from the internet update software. Updateable products include Max Energy 2.0, Max Energy, Speedometer Calibrator, Interceptor, and Inline Speedometer Calibrator (device configuration only). Most Hypertech products are easily updated over the internet using Hypertech’s internet update software for Windows. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |